RCRCM 2900mm F3F Glider – Strega
The Strega makes for an excellent F3F sport model. If looking for something that's fast and can maintain energy on it's turns, then Strega is for you!! The elliptical planform supports a very large speed envelope, with no nasty habits at low speed. The wing is two part, with a carbon joiner and a removable V-Tail. The wings and fuse are ready for your plug and play multiplex setup, allowing for super fast setups at the field or slope. The fit and finish of the Strega is similar to much more expensive models, yet it still has an industry leading level of pre-assembly!
Supported by a large carbon wing joiner, the plug-in wings are of elliptical plan form which has been optimized to give a compromise between good lift distribution without the attendant tip stalling behavior sometimes seen in truly elliptical plan forms. Fin and tailplane sections are also of advanced symmetrical design and have no drag bucket at any speed. Glider for experienced pilots, Strega offers outstanding performance and excellent thermal flight qualities. It is also able to pick up speed, to convince you. It is able to fly in virtually all conditions and it is equipped with ailerons, flaps and a motor. All surfaces are pre-painted in the molds for flawless external finish. The whole model uses live hinges and wipers for control surfaces. From its super-efficient V-Tail, to its new larger diameter nose area, this little guy was built for fun!
Available in 4 Versions:
Fiberglass+Carbon Standard Version: Standard hollow molded fiberglass construction reinforced with carbon fiber which gives adequate stiffness and torsion stability with lower weigh and cost. Highly recommended for sport flying.
Carbon Version: Wings built using carbon cloth as well as fuselage reinforced with carbon from leading edge of the wing to the tail. This configuration gives the model enormous stiffness and torsion stability.
The first two versions are available in stock. Besides, we have Light Carbon Version(less weight) and Double Carbon Version(with two layers of carbon), the last two versions are customized.
- Control Surfaces: V-tail, Ailerons and Flaps
- Two-piece hollow molded composite Carbon or Fiberglass wing design
- Carbon Fiber reinforced wing with square wing joiner
- Live hinges on the wing and rudder with pre-installed wipers
- Smooth, gel-coated finish with pre-painted graphics
- Fuselage hatch for V-tail servos
- Glider fiberglass or full carbon with a beautiful finish comes with all necessary accessories for mounting
- 2900mm Wingspan F3F Glider – Strega
- Ballast Tube(for Motorless Glider only) , Motor mount(for electric version only), servo support, Push Rod, Clevis, Linkage Rod, Control horn, Servo Cover, Wing joiner, tail joiner, servo plate
Wing area: 56.3dm2
Flying Weight: N/A
Empty Weight: Fiberglass+Carbon Standard Version:1610g
Carbon Version: 1720g
CG: 102-110 mm from leading edge
Tow hook setting NO
Required Radio No less than 7 channels
Recommend equipment configuration for an electric version basic configuration
Servos for wings KST DS125MG*4
or RCRCM DS190MG*4
Servos for fuselage KST DS215MG*2
or RCRCM DS296MG*2
Required Battery 4S 14.8V 2600mah 25c
Power System LC3542-7T KV780
Motor Mount Dia. 38mm
Electronic Speed Control SkyWalker-60A
Fairing size 40mm
Paint Scheme is also available in a wide range of colors, besides standard color scheme presents on this website, also include some other color schemes.
Another important thing is about the surface of airplane: RCRCM airplane is fully moulded, Mould precision ensures that each airplane has a complete aerodynamic layout. Yet in the process of composite airplane production, there seldom causes little tiny air bubbles, slight cloth grain, it shouldn’t be regard as a quality issue if it doesn’t affect flight.
About how to storage airplane in case you don’t fly it for a long time: It is better to keep airplane vertical hanging. Never give stress onto airplane surface, so as to avoid deformation.